Instant documents for 2 to 4 units, from $2,000: generated from your answers and ready the moment you pay. See how it works

Plats, plans and recording

Every Texas condo needs a plat, and an attached condo also needs floor plans. They're simpler than most people expect: footprints and unit lines, with no room layouts or interior walls. Here's what they show, who signs them, what clean ones look like, and what you need to record.

What you need

PlatFloor plans
Detached (site) condoYesNo. The unit lines run along the ground, so the plat shows them.
Attached condo, side by sideYesYes: each unit's outline on each floor, and its floor and ceiling elevations
Attached condo, stackedYesYes, for each level, with the elevations that separate the units

Who signs them

Chapter 82 lets an independent licensed surveyor or engineer certify the plat that shows the condo's outer boundaries and locates the buildings (§82.059(g)). But that plat is a land survey, and Texas reserves land surveying to registered surveyors (Occupations Code ch. 1071), so in practice a Registered Professional Land Surveyor prepares, seals and certifies it. Floor plans, and any other plat, can be certified by an independent licensed architect, engineer or surveyor, using elevations from your surveyor. Each certification states that the drawing contains all the information Section 82.059 of the Texas Property Code requires, and the professional signs and seals it.

What the plat shows

Under Chapter 82, a condominium plat is a survey (§82.003(a)(19)). For a project with no development rights reserved, which covers everything we do, it must also show everything the law requires on any land survey (§82.059(b)(11)). So the plat starts as a full boundary survey of the property: monuments at the corners, bearings and distances on every line, the adjoining lots and the street, recorded easements and building lines with their recording data, the area, and the surveyor's notes. On top of that, it shows:

  • The condo's name, and the location and dimensions of the land and of any existing buildings and improvements
  • Encroachments, recorded easements, and utility lines the owner knows were built outside a recorded easement
  • A note listing every recorded easement and license in Schedule B of the title commitment that benefits or burdens the property, with its recording data, including any that can't be drawn. The plat is part of the declaration (§82.059(a)), and our declaration relies on this list for the recorded easements and licenses §82.055(10) requires it to describe, so give your surveyor the commitment.
  • Each unit's boundaries, located and dimensioned, and its name, where the plans don't show them. In a detached (site) condo, every unit line gets a bearing and distance, tied to the lot lines.
  • Every area outside the units reserved for one unit, such as a parking pad or patio, located and dimensioned and labeled with that unit's name
  • Distances and bearings locating each building from the others and from at least one boundary line
  • "MUST BE BUILT" or "NEED NOT BE BUILT" on anything not yet built

What the plans show

To the extent the plat doesn't show them: each unit's vertical boundaries on each floor, located and dimensioned, with the unit's name, and its upper and lower boundaries as elevations referenced to an established datum (§82.059(d)). The plans tie to the land through the plat, which locates each building from the lot lines. That's all. Interior walls and room layouts aren't required, and leaving them out keeps the plans from conflicting with your marketing materials or a future remodel.

One rule that matters for reserved areas

Anything inside a unit's lines belongs to that unit. Anything outside the units is owned in common. Our declaration gives each area the plat labels for one unit, like "Pad A" or "Patio B," to that unit, and on that question the plat controls. So check the labels before your surveyor certifies the plat.

Sample sheets

Clean, simple sheets for each kind of condo, drawn for this page to show what a good set contains. The properties are made up, and these aren't real plats; your surveyor's will follow their own layout.

Detached (site) condo: the plat

Live Oak Condominiums, Condominium plat, sheet 1 of 1: a sample sheet drawn for this page SAMPLE 1/2″ IRF 1/2″ IRF 1/2″ IRF 1/2″ IRF N 89°52′14″ E 130.00′ S 89°52′14″ W 130.00′ S 00°07′46″ E 70.00′ N 00°07′46″ W 70.00′ Live Oak Street (50′ right-of-way) Lot 6, Block 2 Lot 8, Block 2 Lot 14, Block 2 10′ utility easement, Vol. 12, Pg. 34 25′ building line Point of beginning: 1/2″ iron rod found at the northwest corner of Lot 7 N 010′20 feet Pad A12′ × 18′ Pad B12′ × 18′ Generalcommonelement:shared drive Existing house48.0′ × 22.0′ ADU, 26.0′ × 20.0′MUST BE BUILT Unit A3,990 sq. ft. Unit B3,990 sq. ft. N 89°52′14″ E 114.00′ (unit line) S 00°07′46″ E 35.00′S 00°07′46″ E 35.00′ 16.00′114.00′ 16.00′114.00′ 34.0′8.0′ 46.0′6.0′14.0′ Live Oak Condominiums Lot 7, Block 2, Live Oak Addition Travis County, Texas A two-unit site condominium Condominium plat, sheet 1 of 1 Notes 1. Bearings are based on the recorded plat of Live Oak Addition, Vol. 12, Pg. 34, Plat Records of Travis County. 2. Lot 7 contains 9,100 square feet (0.209 acre). 3. Surveyed on the ground on [date], with the benefit of title commitment GF No. [number]. 4. Flood zone X (outside the 0.2% annual chance floodplain), FEMA panel 48453C0465K. 5. No encroachments were observed. 6. Building walls are parallel to the lot lines; ties are measured square to them. 7. Each unit is the land within its unit lines and everything on it, with no upper or lower boundary. 8. Pad A and Pad B (12′ × 18′, each 2.0′ from the west lot line and 2.0′ from the north or south lot line) are limited common elements of the unit named; the rest of the drive is a general common element. Legend Condominium boundary Unit boundary Limited common element (LCE) Easement or building line 1/2″ iron rod found (IRF) Certification I certify that this plat was prepared from an actual survey made on the ground under my supervision and that it contains all information required by Section 82.059 of the Texas Property Code. Seal Registered Professional Land Surveyor Texas Registration No. ____
A house and a detached ADU. One sheet does it. It's a full boundary survey of the lot (monuments, adjoining lots, the street, recorded easements, area and survey notes) that also shows each unit's lines with bearings and distances, each building tied to the lot lines and to the other building, the pads reserved for each unit with their dimensions, and the surveyor's certification. No floor plans needed.

Attached condo, side by side: the plat

Live Oak Condominiums, Condominium plat, sheet 1 of 2: a sample sheet drawn for this page SAMPLE 1/2″ IRF 1/2″ IRF 1/2″ IRF 1/2″ IRF N 89°52′14″ E 130.00′ S 89°52′14″ W 130.00′ S 00°07′46″ E 70.00′ N 00°07′46″ W 70.00′ Live Oak Street (50′ right-of-way) Lot 6, Block 2 Lot 8, Block 2 Lot 14, Block 2 10′ utility easement, Vol. 12, Pg. 34 25′ building line Point of beginning: 1/2″ iron rod found at the northwest corner of Lot 7 N 010′20 feet Pad A12′ × 18′ Pad B12′ × 18′ Patio A14′ × 14′ Patio B14′ × 14′ Unit Aboundaries on Sheet 2 Unit Bboundaries on Sheet 2 Two-story duplex, 60.0′ × 56.0′, MUST BE BUILT 38.0′7.0′32.0′ Shared drive Live Oak Condominiums Lot 7, Block 2, Live Oak Addition Travis County, Texas A two-unit attached condominium Condominium plat, sheet 1 of 2 Notes 1. Bearings are based on the recorded plat of Live Oak Addition, Vol. 12, Pg. 34, Plat Records of Travis County. 2. Lot 7 contains 9,100 square feet (0.209 acre). 3. Surveyed on the ground on [date], with the benefit of title commitment GF No. [number]. 4. Flood zone X (outside the 0.2% annual chance floodplain), FEMA panel 48453C0465K. 5. No encroachments were observed. 6. Building walls are parallel to the lot lines; ties are measured square to them. 7. Unit boundaries are shown on Sheet 2. Everything outside the units is a common element. 8. Pads (12′ × 18′, 2.0′ from the west and north or south lot lines) and patios (14′ × 14′, against the east wall, 6.0′ from its north or south face) labeled A or B are limited common elements of the unit named. Legend Condominium boundary Unit boundary Limited common element (LCE) Easement or building line 1/2″ iron rod found (IRF) Certification I certify that this plat was prepared from an actual survey made on the ground under my supervision and that it contains all information required by Section 82.059 of the Texas Property Code. Seal Registered Professional Land Surveyor Texas Registration No. ____
Sheet 1 is the boundary survey. It ties the building to the lot lines and shows the pads and patios reserved for each unit, with their dimensions. The unit boundaries are on Sheet 2.

Attached condo, side by side: the plans

Live Oak Condominiums, Condominium plans, sheet 2 of 2: a sample sheet drawn for this page SAMPLE Unit AUnit B First floor Building: 60.0′ (exterior) 56.0′ (exterior) 59.0′ × 26.9′59.0′ × 26.9′ Unit AUnit B Second floor Building: 60.0′ (exterior) 56.0′ (exterior) 59.0′ × 26.9′59.0′ × 26.9′ Horizontal unit boundaries UnitLower boundaryUpper boundary AElev. 501.20′Elev. 520.70′ BElev. 501.20′Elev. 520.70′ Vertical boundaries: the unfinished interior surfaces of each unit's perimeter walls, dimensioned above (inside dimensions). Lower boundary: the unfinished surface of the lowest floor. Upper boundary: the unfinished surface of the highest ceiling. Elevations refer to NAVD 88. Interior walls and room layouts are not shown; Section 82.059 doesn't require them. Live Oak Condominiums Lot 7, Block 2, Live Oak Addition Travis County, Texas A two-unit attached condominium Condominium plans, sheet 2 of 2 Notes 1. Each unit is the space inside its boundaries; walls, roof, structure and land are common elements. 2. The building is located on Sheet 1, tied to the lot lines. 3. Unit dimensions are to the unfinished interior surfaces of the perimeter walls, 0.5′ inside the building's exterior faces. The party wall between the units is a common element. Certification I certify that these plans contain all information required by Section 82.059 of the Texas Property Code. Seal Licensed architect, engineer or surveyor Texas License No. ____
Sheet 2 dimensions each unit's outline on each floor and gives its floor and ceiling elevations. That's all: no room layouts.

Attached condo, stacked: the plans

Pecan Street Condominiums, Condominium plans, sheet 2 of 2: a sample sheet drawn for this page SAMPLE Unit B Level 1 Unit A Level 2 40.0′ (exterior)52.0′ (exterior) 39.0′ × 51.0′ 40.0′ (exterior)52.0′ (exterior) 39.0′ × 51.0′ Section (side view) Unit AUnit B 520.70′ 510.95′ 510.10′ 501.20′ Horizontal unit boundaries UnitLower boundaryUpper boundary A (Level 2)Elev. 510.10′Elev. 520.70′ B (Level 1)Elev. 501.20′Elev. 510.95′ Inside dimensions are to the unfinished interior surfaces of the perimeter walls (the vertical boundaries). The floor between the units, the roof, walls and structure are common elements. Elevations refer to NAVD 88. Interior walls and room layouts are not shown. Pecan Street Condominiums Lot 3, Block 1, Pecan Street Addition Harris County, Texas A two-unit stacked condominium Condominium plans, sheet 2 of 2 Notes 1. Unit B is on Level 1 and Unit A on Level 2. 2. Each unit is the space inside its boundaries. 3. The building is located on Sheet 1 (the plat), drawn like the attached example above. Certification I certify that these plans contain all information required by Section 82.059 of the Texas Property Code. Seal Licensed architect, engineer or surveyor Texas License No. ____
One home above the other. The plans show each level and a side view with the elevations that separate the units.

What recording takes

You or your title company record the documents in the real property records of the county where the land is. The county clerk records a condo declaration without approval from any other office (Tex. Prop. Code §82.051(d)). Before you go, have these ready:

  1. The association formed The certificate of formation is filed with the Texas Secretary of State before you sell the first unit (§82.101). With the full package, we file it; with instant documents, you do.
  2. Lender consent If a lender has a lien on the property, it signs a consent to the declaration, recorded before or with the first unit sale (§82.051(b)). Recording the declaration without a lender's consent can also breach your deed of trust or other loan documents, which usually restrict transferring, dividing or further encumbering the property, and that can let the lender declare a default or call the loan due. Record the signed consent with the declaration.
  3. The signed declaration Everyone who owns an interest in the property signs it before a notary.
  4. The plat and any plans They're signed, sealed and certified as described above, and attached to the declaration.
  5. Tax certificates The clerk won't record a condo plat without an original tax certificate from each taxing unit showing no delinquent property taxes, plus, if a certificate doesn't cover the preceding year, a receipt showing that year's taxes were paid (§82.051(f), as amended in 2025). Order them from the tax office a few days ahead; a MUD or other district may issue its own.
  6. The management certificate Afterward, record the management certificate and file it with the Texas Real Estate Commission (§82.116), and keep the recording numbers for the association's records.

With the full package, our recording package lists each step for your project. With instant documents, the filing and recording checklist does.

Sources

  1. Texas Property Code §82.003(a)(18) and (19) (a plat is a survey; a plan is a dimensional drawing), §82.059 (plats and plans; who certifies them; no interior detail required) and §82.051 (recording; tax certificates).
  2. Texas Property Code §82.101 (association formed before the first conveyance) and §82.116 (management certificate).